View PCFP24-100-U2-PMU-L02-M8_8707655.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pcfp24-bfs1 pcfp24 posichron ? position sensor only 12 mm height and 43 mm width ? protection class up to ip67/ip69k ? measurement range 0 ... 100 to 0 ... 5750 mm ? absolute position measurement ? ultra flat profile housing: only 12 mm high ? easy installation with mounting brackets ? contactless ? absolutely wear free and maintenance-free ? analog output specifcations output voltage current resolution refer to output specifcation sampling rate up to 1 khz, depending on the measurement range linearity ranges >500 mm: l10 = 0.10 % f.s. l02 = 0.02 % f.s. ranges 500 mm: l10 = 0.5 mm l02mm = 0.2 mm repeatability 3 m housing material almgsi1 / zn / v4a protection class ip67 (optional ip67/ip69k; connector version: with mating connector only) shock en 60068-2-27:2010, 50 g 11 ms, 100 shocks vibration en 60068-2-6:2008, 20 g 10 hz-2 khz, 10 cycles connection 4 pin socket m8 / cable 2 m emc, temperature refer to output specifcation order code mounting set (see page 7) posichron ? pcfp24 flat profile housing with analog output 1 channel order code pcfp24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request output u1 = 0 ... 10 v signal conditioner u1/h = u1 with alarm_hold (see page 10) u2 = 0.5 ... 10 v signal conditioner u2/u; u2/h = u2 with alarm_low; u2 with alarm_hold (see page 10) u8 = 0.5 ... 4.5 v signal conditioner u8/u; u8/h = u8 with alarm_low; u8 with alarm_hold (see page 10) i1 = 4 ... 20 ma signal conditioner (3 wire) i1/u; i1/h = i1 with alarm_low; i1 with alarm_hold (see page 10) function and characteristics output p1a = position magnet 1, increasing p1d = position magnet 1, decreasing pmu = start value, direction & end value adjustable by the customer linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection m8 = connector m8, 4 pin kab2m = cable, standard length 2 m, other lengths upon request db-pcfp24-e-2013 www.asm-sensor.com 1/14 ? asm gmbh info@asm-sensor.com
pcmag5 kab-...m-m8/4f/g-litze pcfp24 pcfp24 order code mating connecting cable (see page 14) order code position magnet (see page 7) posichron ? pcfp24 flat profile housing with analog output 1. order example: pcfp24 - 1000 - i1 - p1a - p2d - l10 - kab2m flat profle, measurement range 1000 mm, 2 current outputs 4 ... 20 ma (i1) output 1: position magnet 1, increasing signal (p1a) output 2: position magnet 2, decreasing signal (p2d) 2. order example: pcfp24 - 1000 - u2 - p1a - vz1.0 - l10 - kab2m flat profle, measurement range 1000 mm, 2 voltage outputs 0.5 ... 10 v (u2) output 1: position magnet 1, increasing signal (p1a) output 2: velocity magnet 1, -1 m/s ... 1 m/s for range 0.5 ... 10 v (vz1.0) order code pcfp24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request output u1 = 0 ... 10 v signal conditioner u1/h = u1 with alarm_hold (see page 10) u2 = 0.5 ... 10 v signal conditioner u2/u; u2/h = u2 with alarm_low; u2 with alarm_hold (see page 10) u8 = 0.5 ... 4.5 v signal conditioner u8/u; u8/h = u8 with alarm_low; u8 with alarm_hold (see page 10) i1 = 4 ... 20 ma signal conditioner (3 wire) i1/u; i1/h = i1 with alarm_low; i1 with alarm_hold (see page 10) function and characteristics output 1 p1a = position magnet 1, increasing p1d = position magnet 1, decreasing da = difference magnet 1/2, increasing (2 magnets required) dd = difference magnet 1/2, decreasing (2 magnets required) function and characteristics output 2 p2a = position magnet 2, increasing p2d = position magnet 2, decreasing da = difference magnet 1/2, increasing dd = difference magnet 1/2, decreasing vzx.x = velocity with direction detection (with 1 magnet only) vzx.x = velocity in steps of 0.1 m/s example: vz1.5 towards start position towards end position -1.5 m/s 0 +1.5 m/s output u2: 0.5 v 5.25 v 10 v output i1: 4 ma 12 ma 20 ma vax.x = velocity without direction detection (with 1 magnet only) vax.x = velocity in steps of 0.1 m/s example: va1.5 towards start position towards end position -1.5 m/s 0 +1.5 m/s output u2: 10 v 0.5 v 10 v output i1: 20 ma 4 ma 20 ma linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection kab2m = cable, standard length 2 m, other lengths upon request 2 channel, confgurable 2 magnets required db-pcfp24-e-2013 www.asm-sensor.com 2/14 ? asm gmbh info@asm-sensor.com
pcmag5 pcfp24-bfs1 / / pcfp24 / / posichron ? position sensor only 12 mm height and 43 mm width ? protection class up to ip67/ip69k ? measurement range 0 ... 100 to 0 ... 5750 mm ? absolute position measurement ? ultra flat profile housing: only 12 mm high ? easy installation with mounting brackets ? contactless ? absolutely wear free and maintenance-free ? synchronous serial interface (ssi) specifcations output synchronous serial (ssi) resolution 5, 10, 20, 50, 100 m sampling rate up to 1 khz, depending on the measurement range linearity ranges >500 mm: l10 = 0.10 % f.s. l02 = 0.02 % f.s. ranges 500 mm: l10 = 0.5 mm l02mm = 0.2 mm repeatability 3 m housing material almgsi1 / zn / v4a protection class ip67 (optional ip67/ip69k; connector version: with mating connector only) shock en 60068-2-27:2010, 50 g 11 ms, 100 shocks vibration en 60068-2-6:2008, 20 g 10 hz-2 khz, 10 cycles connection cable 2 m emc, temperature refer to output specifcation order example: pcfp24 - 2000 - 5 - ssi/g/24 - l02 - kab2m posichron ? pcfp24 flat profile housing with ssi output order code position magnet (see page 7) order code mounting set (see page 7) order code pcfp24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request resolution (in m) 5 / 10 / 20 / 50 / 100 output ssi = synchronous serial interface code g / d = gray / dual number of data bits 24 / 25 linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection kab2m = cable, standard length 2 m, other lengths upon request db-pcfp24-e-2013 www.asm-sensor.com 3/14 ? asm gmbh info@asm-sensor.com
pcmag5 pcfp24-bfs1 kab-...m-m12/5f/g-m12/5m/g - can pcfp24 posichron ? position sensor with only 12 mm height and 43 mm width ? protection class up to ip67/ip69k ? measurement range 0 ... 100 to 0 ... 5750 mm ? absolute position measurement ? ultra flat profile housing: only 12 mm high ? easy installation with mounting brackets ? contactless ? absolutely wear free and maintenance-free ? canopen bus or can sae j1939 output ? redundant version: combination of 2 sensors side by side specifcations output canopen bus; can sae j1939 resolution 50 m sampling rate up to 1 khz, depending on the measurement range linearity ranges >500 mm: l10 = 0.10 % f.s. l02 = 0.02 % f.s. ranges 500 mm: l10 = 0.5 mm l02mm = 0.2 mm repeatability 3 m housing material almgsi1 / zn / v4a protection class ip67 (optional ip67/ip69k; connector version: with mating connector only) shock en 60068-2-27:2010, 50 g 11 ms, 100 shocks vibration en 60068-2-6:2008, 20 g 10 hz-2 khz, 10 cycles connection cable 0,3 m with 5-pin connector m12 emc, temperature refer to output specifcation posichron ? pcfp24 flat profile housing with can output order code bus cable (see page 14) order code position magnet (see page 7) order code mounting set (see page 7) order example: pcfp24 - 1000 - canop - l10 - kab0,3m-m12/can order code pcfp24 model name measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request output canop = canopen bus canop/r = canopen-bus with integrated terminating resistance canj1939 = can sae j1939 linearity l02 / l02mm / l10 (for defnition see "specifcations" above) connection kab0,3m-m12/can = cable (length 0.3 m) with 5-pin m12 connector db-pcfp24-e-2013 www.asm-sensor.com 4/14 ? asm gmbh info@asm-sensor.com
90 [3. 5 43] 11 ,5 [ 0. 453 ] 10 0 [3 .937] messl?nge (z.b. ) 75 [2.953] 4 3 [ 1 .6 9 3 ] 1 2 [ 0 . 4 7 2 ] 59 [2. 323] 71 [2.795] 3 4 [ 1 . 3 3 9 ] 2 9 [ 1 .1 4 2 ] 10, 2 [0.40 2] 265 [1 0. 433] gesamtl? nge a = me ssl?n ge +1 65 [6 . 496] (z.b. ) befestig un gssatz pcfp24-bfs1 anfan gspositi on pcmag5 endposit i on pcmag5 26 [1. 024] 39 [1.535] 2 1 [ 0 .0 7 9 0 .0 3 9 ] 1 2 [0. 472] ? 12 ,8 [ 0. 50] 1 3 [ 0 .5 1 2 ] 90 [3.5 43] me ssl?nge (z. b. 100 [3. 937] ) 75 [2.953] ges amtl? nge a = me ssl? nge + 1 65 [6.4 96] (z.b. 265 [10. 4 33]) 59 [2 .3 23] 71 [2.7 95] 2 9 [ 1 . 1 4 2 ] 3 4 [ 1 . 3 3 9 ] 1 2 [ 0 .4 7 2 ] 10,2 [0.402] 4 3 [ 1 .6 9 3 ] 26 [ 1. 024] 39 [1. 535] befestig un gssatz pcfp24-bfs1 anfangsposition pcmag5 en dposition pcmag5 14,9 [0 .5 87] 1 3 [ 0 .5 1 2 ] 2 1 [ 0 .0 7 9 0 .0 3 9 ] ? 12 [ 0.47 2] ? 12,8 [0.50] posichron ? pcfp24 flat profile housing start position pcmag5 mounting set pcfp24-bfs1 end position pcmag5 total length a = measurement length + 165 [6.496] (e.g. 265 [10.433]) measurement length (e.g. 100 [3.937]) start position pcmag5 mounting set pcfp24-bfs1 end position pcmag5 total length a = measurement length + 165 [6.496] (e.g. 265 [10.433]) measurement length (e.g. 100 [3.937]) &deoh rxwsxw &rqqhfwru 0 cable: outer diameter 5.2 mm 0.2 mm, wire: cross sectional area 0.25 mm2 dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] dimensions informative only. for guaranteed dimensions consult factory. dimensions in mm [inch] db-pcfp24-e-2013 www.asm-sensor.com 5/14 ? asm gmbh info@asm-sensor.com
43 [1. 693 ] 2 0 [ . 7 8 7 ] 1 1 , 1 [ . 4 3 7 ] 5 , 8 [ . 2 2 8 ] 37,4 [1.472] 55 [2.165] 25 [.984] 20 [.787] 1 7 , 5 [ . 6 8 9 ] 5 [ . 1 9 7 ] 5 [ . 1 9 7 ] 4 2 , 5 [ 1 . 6 7 3 ] 2 [. 07 9] r2 , 7 5 [ . 1 08 ] 4x 36 [1.417 ] 2 0 [ . 7 8 7 ] 1 1 , 1 [ . 4 3 7 ] 5 , 8 [ . 2 2 8 ] 30,4 [1.197] 55 [2.1 65] 5 [ . 1 9 7 ] 5 [ . 1 9 7 ] 15 [. 59 1] 20 [. 78 7] 1 7 , 5 [ . 6 8 9 ] 4 2 , 5 [ 1 . 6 7 3 ] 2 [.079] r 2 , 7 5 [ . 1 0 8 ] 4 x option -bfw mounting brackets for pcfp24 note: the option -bfw can only be ordered with a new sensor, not separately! applicable for sensor lengths up to 1000 mm. not combinable with pcfp24-bfs1. order example: pcfp24 - 1000 - stsp - l02 - m8 - bfw order example: pcfp23 - 1000 - stsp - l02 - m8 - bfw db-pcfp24-e-2013 www.asm-sensor.com 6/14 ? asm gmbh info@asm-sensor.com
55 43 1 2 9 1 2 55 43 1 0 befestigung pcfp25 befe stigung pcfp 25 din 912 - m4 x 16 din 125 - a4 isolierscheibe isol ie rstr eifen pc qa-bfs4 din 912 - m5 x 10 din 125 - a5 is ol iert nic ht is oliert posichron ? pcfp onting sets - agnets dimensions bfs1 posichron model dim. b dim. c pcmag5 standard magnet imensions in mm inh isolation strip onting lamp p isolation sleee imensions inormatie only for garanteed dimensions onslt atory imensions in mm inh isolation strip pc-bfs4 isolation sleee onting lamp pcfp2 pcfp23-bfs1 and pcfp24-bfs1 onting set or pcfp23 pcfp24 pcfp25-bfs1 db-pcfp24-e-2013 www.asm-sensor.com 7/14 ? asm gmbh info@asm-sensor.com
i1 u1, u2, u8 posichron ? output specification u2, u8 and i1 configurable, 1 or 2 channels u1, u2, u8 voltage output excitation voltage u1: 18 ... 36 v dc; u2: 18 ... 36 v dc; u8: 10 ... 36 v excitation current typ. 35 ma, 80 ma max. output voltage u1: 0 ... 10 v dc; u2: 0.5 ... 10 v dc; u8: 0.5 ... 4.5 v dc output current 2 ma max. output load > 5 k? resolution 16 bit f.s., min. 10 m stability (temperature) 50 x 10 -6 / c f.s. protection reverse polarity, short circuit output noise 0.5 mv rms operating temperature -40 ... +85 c emc en 61326-1:2013 excitation + excitation gnd signal 1 + signal gnd signal diagram excitation + excitation gnd signal 1 + signal gnd i1 current output (3 wire) excitation voltage 18 ... 36 v dc (10 ... 36 v for r l ?) excitation current typ. 60 ma, 80 ma max. load resistor 350 ? max. output current 4 ... 20 ma, 30 ma max (at failure) resolution 16 bit f.s., min. 10 m stability (temperature) 50 x 10 -6 / c f.s. protection reverse polarity, short circuit output noise 0.5 mv rms operating temperature -40 ... +85 c emc en 61326-1:2013 span/zero (pmu, as option) signal 2 + (as option) span/zero (pmu, as option) signal 2 + (as option) signal diagram signal diagram db-pcfp24-e-2013 www.asm-sensor.com 8/14 ? asm gmbh info@asm-sensor.com
posichron ? output specification u2, u8 and i1 configurable, 1 or 2 channels signal plug connection cable connection view to the sensor connector excitation + 1 white excitation gnd 2 brown signal 1 + 3 green signal gnd 4 yellow signal 2 + (optional*) 5 grey span/zero (pmu** only, optional) 6 pink connector m12, 8-pin signal wiring * when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** description page 10 signal plug connection view to the sensor connector excitation + 1 signal 1 + 2 gnd 3 signal 2 + (optional*) 4 pmu** (optional) 5 connector m12, 5-pin signal wiring * when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** description page 10 signal plug connection view to the sensor connector excitation + 1 excitation gnd 2 signal + 3 pmu** (optional) 4 connector m8, 4-pin signal wiring * when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** description page 10 db-pcfp24-e-2013 www.asm-sensor.com 9/14 ? asm gmbh info@asm-sensor.com
option - pmu for analog output u1, u2, u8 and i1 programming of the start and end value by the customer: the option pmu allows to program the start value and the end value of the output range by a programming signal span/zero available at the connector. this signal span/zero must be connected with gnd via a push button, then position magnet of the sensor must be moved to the start resp. end position. pushing the button between 2 and 4 seconds sets the actual position as start position, pushing the button more than 5 seconds sets the actual position as end position. the values will be stored and are available after switching off the sensor. to reset the sensor to the factory values the button must be pushed for longer than two seconds when the sensor is switched on. posichron ? description of output options diagnostic on analog outputs error signal for ssi output if the sensor cannot detect a magnet the position value will assume the maximum value (0xfffffff). alarm_high (standard) alarm_low (.../u) alarm_hold (.../h) u1 u out 10,5 v keeps last valid state ( order code u1/h) u2 u out 10,5 v u out < 0,25 v ( order code u2/u) keeps last valid state ( order code u2/h) u8 u out 10 v u out < 0,25 v ( order code u8/u) keeps last valid state ( order code u8/h) i1 i out 21 ma 1,5 ... 2 ma (order code i1/u) keeps last valid state ( order code i1/h) behaviour of the analog signal output in case of error in case of error (magnet missing or outside the measuring range) the analog output signal will assume a state according to the following options: alarm_high the output voltage resp. the output current is at high level (overrange). alarm_low the output voltage resp. the output current is at low level (underrange). alarm_hold the output voltage resp. the output current will keep the last valid state. db-pcfp24-e-2013 www.asm-sensor.com 10/14 ? asm gmbh info@asm-sensor.com
posichron ? output specification ssi description the data transmission takes place by means of the two signals clock and data. the pro - cessing unit (plc, microcomputer) sends pulse sequences which clock the data transmissi - on at the required transfer rate. with the first falling edge of the pulse sequence the position of the sensor is recorded and stored. the following rising edges control the bit-by-bit transfer of the data word. after a delay time the next new position information can be transwithted. data format (train of 26 pulses) synchronous serial interface ssi output rs422 excitation voltage 10 ... 36 v dc, residual ripple 10 mv ss excitation current typ. 80 ma, 150 ma max. clock frequency 100 khz ... 1 mhz code gray code, dual code resolution 5 m delay between pulse trains >25 s stability (temperature) 50 x 10 -6 / c f.s. operating temperature -40 ... +85 c emc en 61326-1:2013 sensor circuit subsequent circuit cable length baud rate 50 m 100-1000 khz 100 m 100-300 khz note: extension of the cable length will reduce the maximum transmission rate. the signals clock/ clock and data/ data must be connected in a twisted pair cable, common shielded. clock clock data data signal diagram error indication see page 10. signal wiring signal plug connection cable connection view to sensor connector excitation + 1 white excitation gnd 2 brown clock 3 green clock 4 yellow data 5 grey data 6 pink db-pcfp24-e-2013 www.asm-sensor.com 11/14 ? asm gmbh info@asm-sensor.com
view to sensor connector posichron ? output specification canopen interface canop communication profle canopen cia 301 v 4.02, slave encoder profle encoder cia 406 v 3.2 error control node guarding, heartbeat, emergency message node id adjustable via lss or via object dictionary pdo 4 txpdo, 0 rxpdo, no linking, static mapping pdo modes event-/time triggered, remote-request, sync cyclic/acyclic sdo 1 server, 0 client cam 8 cams certifed yes transmission rates 50 kbaud to 1 mbaud, adjustable via lss or via object dictionary nodes 127 max. bus connection m12 connector, 5 pins integrated bus terminating resistor 120 :(option) bus, galvanic isolated no description canopen interface with process data for position and cam functions, programmable are preset, resolution, filtering and cam switching points. specifcations excitation voltage 18 ... 36 v dc excitation current typ. 20 ma for 24 v, max. 80 ma number of position magnets 1 ... 4 resolution 50 m measuring rate 1 khz (asynchronous) stability (temperature) 50 x 10 -6 / c f.s. repeatability 1 lsb operating temperature -40 ... +85 c protection reverse polarity, short circuit dielectric strength 500 v (v ac, 50 hz, 1 min.) emc en 61326-1:2013 signal wiring signal plug connection shield 1 excitation + 2 gnd 3 can-h 4 can-l 5 when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. db-pcfp24-e-2013 www.asm-sensor.com 12/14 ? asm gmbh info@asm-sensor.com
posichron ? output specification can sae j1939 interface j1939 can specifcation iso 11898, basic and full can 2.0 b transceiver 24v-compliant, not isolated communication profle sae j1939 baud rate 250 kbit/s internal temination resistor 120 :(option) address default 247d, confgurable specifcations excitation voltage 18 ... 36 v dc excitation current typ. 20 ma for 24 v, max. 80 ma measuring rate 1 khz (asynchronous) stability (temperature) 50 x 10 -6 / c f.s. repeatability 1 lsb operating temperature -40 ... +85 c protection reverse polarity, short circuit dielectric strength 500 v (v ac, 50 hz, 1 min.) emc en 61326-1:2013 signal wiring signal plug connection shield 1 excitation + 2 gnd 3 can-h 4 can-l 5 name fields arbitrary address capable 0 no industry group 0 global vehicle system 7fh (127d) non specifc vehicle system instance 0 function ffh (255d) non specifc function instance 0 ecu instance 0 manufacturer 145h (325d) manufacturer id identity number 0nnn serial number 21 bit parameter group numbers (pgn) confguration data pgn ef00h proprietary-a (pdu1 peer-to-peer) process data pgn ffnnh proprietary-b (pdu2 broadcast); nn group extension (ps) confgurable view to sensor connector when using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. db-pcfp24-e-2013 www.asm-sensor.com 13/14 ? asm gmbh info@asm-sensor.com
kab - xm - m8/4f/w - litze kab - xm - m8/4f/w/69k - litze ip69k: kab - xm - m8/4f/g - litze kab - xm - m8/4f/g/69k - litze ip69k: kab - xm - m12/5f/g - m12/5m/g - can kab - xm - m12/5f/g/69k - m12/5m/g/69k - can ip69k: kab - tconn - m12/5m - 2m12/5f - can kab - rterm - m12/5m/g - can connector cable m8, 4-pin shielded the 4-lead shielded cable is supplied with a mating 4-pin 90 m8 connector at one end and 4 wires at the other end. available lengths are 2, 5 and 10 m. wire: cross sectional area 0.14 mm2. order code: length in m connector cable m8, 4-pin shielded the 4-lead shielded cable is supplied with a mating 4-pin m8 connector at one end and 4 wires at the other end. available lengths are 2, 5 and 10 m. wire: cross sectional area 0.14 mm2. order code: length in m signal wiring m8, 4-pin plug connection / cable connection 1 2 3 4 brown white blue black posichron ? accessories connector cables connector/bus cable m12, 5-pin can bus shielded the 5-lead shielded cable is supplied with a female 5-pin m12 connector at one end and a male 5-pin m12 connector at the other end. available lengths are 0.3 m, 2 m, 5 m and 10 m. order code: length in m terminating resistance m12, 5-pin can bus t-piece for bus cable m12, 5-pin can bus order code: order code: db-pcfp24-e-2013 www.asm-sensor.com 14/14 ? asm gmbh info@asm-sensor.com

▲Up To Search▲

Price & Availability of PCFP24-100-U2-PMU-L02-M8

	To Download PCFP24-100-U2-PMU-L02-M8 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .